Hyperliquid looks cheap on the fee page, and for a single fill it is. But a perp trade on Hyperliquid pays up to three separate costs: the exchange's trading fee on every fill, a builder fee if you trade through a third-party frontend, and funding every hour you hold the position. Each one is small. Together they decide whether a strategy that looks green on the chart is green in your wallet.
This guide walks through all three with the numbers from Hyperliquid's own documentation, then adds them up on one realistic trade.
1. Trading fees: taker and maker
Hyperliquid charges a fee on every fill. The rate depends on whether your order takes liquidity (taker: market orders, and limit orders that cross the spread) or adds it (maker: resting limit orders).
At the base tier, the Hyperliquid fee schedule lists:
- Taker: 0.045% of notional
- Maker: 0.015% of notional
Your tier comes from your rolling 14-day weighted volume, assessed at the end of each UTC day. Sub-accounts count toward the master account, spot volume counts double, and perps, HIP-3 perps and spot share one tier. Higher tiers lower the rates, and separate maker rebate tiers pay makers with enough maker volume. Two discounts can apply on top: staking HYPE, and a referral code (4% off your fees for your first $25M of volume, per the docs). Check the live fee page for the current tier table, because Hyperliquid changes it from time to time.
On a $10,000 position, the base tier means:
taker fill: 10,000 × 0.045% = $4.50
maker fill: 10,000 × 0.015% = $1.50
A round trip (open and close) with two market orders costs $9.00. The same round trip with two resting limit orders costs $3.00. The order type alone changes your cost by a factor of three. To see what fees leave of your own trade, use the Hyperliquid PnL calculator.
2. Builder fees: the cost you may not have noticed
Many traders do not use the Hyperliquid app directly. They trade through a wallet, a trading bot or another frontend. These apps can attach a builder code to your orders and charge a builder fee on top of the exchange fee. You approve this once, with a signature from your main wallet that sets the maximum rate the app may charge.
According to the builder codes docs, a builder fee can be at most 0.1% on perps (both sides of the trade) and 1% on spot (sell side only).
The cap on perps is more than twice the base taker fee. If an app charges, say, 0.05% per fill, the $10,000 round trip from above costs:
exchange taker fees: 2 × $4.50 = $9.00
builder fees: 2 × $5.00 = $10.00
total: $19.00
More than half the trading cost goes to the app, not to the exchange. Hyperliquid books the builder fee inside the fee of each fill, so in the fill history it looks like one number. If you approved a builder once and forgot, your fees are higher than the fee page suggests.
3. Funding: paid every hour
Perpetual futures have no expiry. Funding is the periodic payment between longs and shorts that keeps the perp price close to spot. Hyperliquid differs from most centralized exchanges in two ways, per its funding docs:
- Funding is paid every hour, not every 8 hours. The rate formula is defined on an 8-hour basis, and each hour you pay or receive one eighth of it.
- The cap is 0.5% per hour, much looser than typical CEX caps.
The rate has two parts. A fixed interest component of 0.01% per 8 hours (0.00125% per hour, 11.6% a year, paid to shorts), and a premium that follows how far the perp trades from the oracle price. When the rate is positive, longs pay shorts; when it is negative, shorts pay longs. The payment is position size × oracle price × funding rate, so it uses the oracle price, not the mark price.
Funding settles at the top of every UTC hour. A position opened and closed between two full hours pays no funding at all; every full hour your position is open across counts once. A swing trade cannot dodge it: with 24 settlements a day instead of three, every day you hold costs you 24 payments. If funding sits at the interest baseline and you hold a $10,000 long across 48 hourly settlements:
10,000 × 0.00125% × 48 settlements = $6.00
In a trending market the premium part can be many times the baseline, and then funding becomes the largest cost of a swing trade. To run the numbers for your own position and hold time, use the Hyperliquid funding rate calculator.
Adding it up on one trade
Take one $10,000 BTC long, opened and closed with market orders, held for 48 hours at baseline funding, aiming for a 1% move ($100 gross):
| Cost | Direct on Hyperliquid | Through an app with a 0.05% builder fee |
|---|---|---|
| Taker fees (2 fills) | $9.00 | $9.00 |
| Builder fees (2 fills) | $0.00 | $10.00 |
| Funding (48 h) | $6.00 | $6.00 |
| Total cost | $15.00 | $25.00 |
| Share of $100 gross | 15% | 25% |
A quarter of the winning trade is gone before you count the losing ones. On losing trades the costs come on top of the loss. Over a few hundred trades, this is often the difference between a strategy that works and one that only looks like it works.
Why your Hyperliquid PnL does not show this
The Hyperliquid app shows trading fees per fill and funding in a separate history. Neither view adds them up per trade, and neither tells you what share of your gross profit went to costs. Builder fees hide inside the fee column. To see the real cost of your trading, you have to join fills and funding per position yourself, or export the history and do it in a spreadsheet (our guide on exporting Hyperliquid trade history shows how).
Check your own wallet
The Hyperliquid wallet check does this join for any public wallet address. Paste the address and you see the closed trades' gross result, fees, funding paid and received, the builder fees inside the fees, and what share of gross went to costs. No account, no signature, and the address is not stored.
If you want this per trade and over time, PerpLog's Hyperliquid trading journal syncs your fills and funding from the wallet address and shows net PnL after every cost, per trade, setup and symbol.
Fee and funding figures are taken from the Hyperliquid documentation as of November 2026. Hyperliquid can change tiers and rates; the linked docs pages are the source of truth.